Do you want to start a motorcycle? If it's in good condition, it shouldn't be difficult. Read this basic tutorial to start a motorcycle!
Method
1
Analyze the situation
Image titled Start a Motorcycle Step 1
1
Determine if the motorcycle has a carburetion system or runs on fuel injection. Many motorcycles, especially older and cheaper ones, do not have a modern fuel injection system. If you are not sure, examine the control valve. It is usually located on the left handlebar, under the horn. Carbureted motorcycles have a primer, but fuel injection motorcycles do not. [1]
2
Sit on the bike to start it. So you will have full control of everything that happens when you turn it on. If for any reason you decide to start the motorcycle without sitting on it, make sure to put it in neutral (between the first and second gear) before starting the engine. You don't want the bike to go without you!
Image titled Start a Motorcycle Step 3
3
Make sure the motorcycle is in good condition. It must have fuel and the battery must be charged. Proper services are important, especially if you are in a cold and humid environment. Put in new spark plugs. If they are not worn, calibrate them. Examine the ignition timing and adjust if necessary. If tight, replace breakout points. A good idea is to check the carburetor and clean it.
Replace the spark plug wires if they are old, worn, or aging. Use only the spark plug wires recommended by the manufacturer. Find the instructions in your motorcycle's owner's manual.
4
Check the oil. Before starting any vehicle, make sure it is lubricated. For this, you will need to check the oil level. If you are out of oil or low on oil, do not start the engine. Otherwise, it will overheat and may break.
Image titled Start a Motorcycle Step 5
5
Check the battery. Put the key in and turn it clockwise until the light comes on. If the lights don't turn on, the battery may be dead and you need to recharge it or put in a new one.
Method
2
Starting a carbureted motorcycle
Image titled Start a Motorcycle Step 6
1
Find the choke lever or kill switch. To start it cold, there is usually a choke lever or a kill switch on the handlebar. On some motorcycles, the choke lever is mounted on the carburetor. Doing this when the engine is cold will provide a rich fuel mixture when it has not been used for more than a few hours. The dirtier the carburetor or the colder the engine, the more you'll need the primer. [2]
You do not need to use the choke lever to start a motorcycle if the engine is hot. If the engine has been running and is still warm, you won't need as much power to start it. You will only have to accelerate a little to get the engine to start. [3]
Many motorcycles have a kill switch on the kickstand, so make sure it's up. If you have the motorcycle in neutral, you will disable the cut with the kickstand.
2
Open the choke lever. Make sure the kill switch is "on." You will need to keep the throttle grip closed when operating the starter or kickstart lever. Otherwise, the engine will flood and starting it will be very difficult and even impossible. Remember: Generally, you don't need to use the choke lever if your motorcycle was in operation for a few hours before. [4]
3
Turn the starter to the "on" position. The dash lights should come on in this position. Also, if the bike is in neutral as suggested, you should notice a green light indicating that it is in the neutral position.
4
Start the engine. Squeeze and hold the clutch lever (located on the left) and press the starter button (located on the right). You should hear the blissful sound of the motorcycle starting.
5
Turn off the choke and open the throttle. Shortly after you start the engine, progressively turn the choke off and open the throttle as the engine warms up. When you are riding the motorcycle, you may need the primer for a short distance. However, try to close the choke as soon as possible so the ride of the motorcycle is smoother. Do not overshoot the motorcycle when it is warming up.
Method
3
Starting a fuel-injected motorcycle
1
Put the motorcycle in neutral. Generally, you will be able to find it between the first and second changes. [5]
Image titled Start a Motorcycle Step 12
2
Don't worry about the primer. On motorcycles with an electronic injection system, the engine management system will automatically take care of fuel needs in the event that the engine is hot or cold. These motorcycles do not have a primer. Use the throttle a bit when you turn it on, whether it's hot or cold
3
Pull the clutch toward the handlebar. It is usually on the left side. Many riders choose to also pull the front brake (located on the right handlebar) at the same time.
4
Press and hold the power button. It is usually located on the right handlebar, near the end where your hand rests.
5
Use the accelerator. If the motorcycle won't start, use the throttle while pressing the power button. While doing this, make sure to hold down the clutch the entire time.
0 Comments